Macintosh SE Capacitor Replacement Guide

Replacing electrolytic capacitors (recapping) in your Macintosh SE is essential for maintaining long-term reliability, consistent power delivery, and clean video output. Aging capacitors can cause instability, poor display quality, or outright system failure. Proactively replacing these components greatly improves the health and performance of your SE.

🔍 Capacitor Inspection

Before beginning a recap, check each capacitor for visual signs of failure:

• Bulging Tops – A domed capacitor top indicates internal gas pressure and failure.
• Leaking Electrolyte – Brown or white crust near the leads signals electrolyte leakage.
• Corrosion or PCB Staining – Green residue or darkened board areas mean urgent replacement is needed.

Use a multimeter with ESR testing capabilities if available to confirm health.

📋 Macintosh SE Capacitor List

🧯 Analog Board Capacitors

The Macintosh SE analog board uses the same layout and component values as the Macintosh Plus, and should be recapped entirely for reliability.

Macintosh SE Analog Board Capacitor Specifications

Label	Capacitance	Voltage	Quantity
C1	3.9µF	35V	1x
C2	4700µF	16V	1x
C3	220µF	16V	2x
C5	47µF	10V	1x
C6	22µF	50V	2x
C10	33µF	16V	2x
C11	10µF	160V	1x
C12	22µF	50V	2x
C18	33µF	16V	2x
C24	2200µF	16V	4x
C27	2200µF	16V	1x
C28	1000µF	16V	1x
C30	2200µF	16V	1x
C31	220µF	16V	1x
C32	2200µF	16V	1x
C33	4700pF	250V	2x
C34	100µF	200V	4x
C35	100µF	200V	1x
C36	4700pF	250V	1x
C37	0.47µF	250V	1x
C38	100µF	200V	1x
C39	100µF	200V	1x
C42	470µF	10V	2x
C45	470µF	10V	1x

💾 Logic Board Capacitors

Macintosh SE Logic Board Capacitor Locations

The Macintosh SE logic board contains only a few electrolytic capacitors but they are vital to system operation.

Macintosh SE Logic Board Capacitor Specifications

Label	Capacitance	Voltage	Quantity
C6	1µF	50V	1x
C1, C3, C4, C5, C7, C8, C9, C10, C12, C13	33µF	10V	10x

> Note: Labeling may differ slightly across board revisions. Double-check values before replacing.

🛠️ Capacitor Replacement Procedure

1. Discharge CRT – Always discharge the CRT before any internal work to prevent injury.
2. Disassemble – Remove the case, analog board, and logic board. Label cables if necessary.
3. Remove Capacitors – Desolder cleanly using a pump or braid. Avoid damaging traces.
4. Install Replacements – Observe polarity markings. Most electrolytics are polarized.
5. Solder Carefully – Apply clean, even solder joints. Trim excess leads.
6. Inspect & Test – Use a multimeter to test continuity and check for accidental shorts.
7. Power Up Carefully – Apply power while monitoring voltages and behavior.

🧰 Recommended Tools

• Temperature-controlled soldering iron (fine tip)
• Desoldering pump or braid
• Multimeter with continuity/ESR testing
• Isopropyl alcohol (99%) and antistatic brush
• Lead-free or leaded 0.5 mm solder
• Protective eyewear and insulated gloves

⚙️ Voltage Adjustment After Recap

After reassembly, verify voltage rails at the floppy drive power plug:

• +5V Rail: 4.85V – 5.15V
• +12V Rail: 11.9V – 12.7V

Use the analog board trimmer potentiometer (R56) to fine-tune if necessary.

💡 Additional Tips

• Power up the SE at least once every few months to keep capacitors healthy.
• Use high-quality brands (e.g., Nichicon, Panasonic, Rubycon).
• Double-check polarity before soldering any capacitor.
• Clean the board of any capacitor residue using alcohol after desoldering.
• Dispose of old capacitors at an approved electronics waste center.

🔗 Related Pages

• Macintosh SE Troubleshooting
• Macintosh SE General Maintenance
• CRT Discharge Procedure