Apple Lisa Capacitor Replacement Guide

Replacing electrolytic and safety capacitors (recapping) in your Apple Lisa is essential for long-term reliability. The Lisa's power supply contains notorious RIFA safety capacitors that fail over time, while electrolytic capacitors throughout the system degrade and can damage circuit boards.

Capacitor Inspection

Before beginning replacement, inspect for:

• Cracked or Bulging Capacitors — RIFA capacitors often show visible cracking in their outer coating
• Electrolyte Leakage — Brown or black residue around capacitor bases indicates leakage
• Corrosion — Green or white deposits on PCB traces near capacitors
• Burn Marks — Discoloration on PCB indicating previous capacitor failure

RIFA Safety Capacitors

The most critical capacitors to replace in any Lisa are the RIFA-brand (or equivalent era) safety capacitors in the power supply. These capacitors are essential for EMI filtering but absorb moisture through their plastic casings over decades, leading to spectacular failures.

RIFA Failure Symptoms

• Loud pop or bang when powering on
• Smoke and acrid smell
• Tripping of household circuit breaker
• Complete power supply failure

RIFA Replacement

ALWAYS replace RIFA capacitors before first power-on of a long-stored Lisa.

Replace with modern X2-rated safety capacitors:

Common RIFA Replacements

Original Value	Voltage	Replacement Type
0.1µF (100nF)	250V AC	X2 Safety Capacitor, 275V AC minimum
0.22µF (220nF)	250V AC	X2 Safety Capacitor, 275V AC minimum
0.047µF (47nF)	250V AC	X2 Safety Capacitor, 275V AC minimum
0.0022µF (2.2nF)	250V AC	Y2 Safety Capacitor (if Y-rated position)

Power Supply Electrolytic Capacitors

The Lisa power supply contains several electrolytic capacitors that should be replaced during a full recap:

Power Supply Electrolytic Capacitors (Typical)

Reference	Capacitance	Voltage	Type
C1	470µF	200V	Electrolytic (main filter)
C2	470µF	200V	Electrolytic (main filter)
C3	1000µF	16V	Electrolytic
C4	47µF	25V	Electrolytic
C5	47µF	25V	Electrolytic
C6	1000µF	16V	Electrolytic
C7	2200µF	16V	Electrolytic

Note: Values may vary by power supply revision. Always verify against your specific unit.

I/O Board Capacitors

The I/O board contains smaller electrolytic capacitors that should be inspected and replaced if showing signs of aging:

I/O Board Capacitors

Typical Values	Voltage	Notes
10µF	16V	Various locations
22µF	16V	Near clock circuits
47µF	16V	Near power input
100µF	16V	Filter capacitors

CPU Board Capacitors

The CPU board also contains electrolytic capacitors:

CPU Board Capacitors

Typical Values	Voltage	Notes
10µF	16V	Various locations
47µF	16V	Near voltage regulators
100µF	10V or 16V	Power filtering

Analog Board Capacitors

The CRT analog board contains both electrolytic and high-voltage capacitors:

Common capacitors include:

• Small signal electrolytics (1µF – 100µF at 16V–50V)
• Filter capacitors near horizontal and vertical deflection circuits
• High-voltage capacitors in the flyback circuit (leave to professionals if uncertain)

Capacitor Replacement Procedure

1. Discharge and Prepare — Unplug Lisa; wait 24+ hours; discharge CRT if accessing analog board
2. Document Original Layout — Photograph capacitor positions and orientations before removal
3. Remove Boards — Remove the power supply or board being serviced
4. Desolder Old Capacitors — Use a temperature-controlled iron; remove old solder
5. Clean Pads — Use solder wick and isopropyl alcohol to clean pads
6. Install New Capacitors — Observe correct polarity (stripe = negative on electrolytics)
7. Solder Securely — Use quality solder; avoid cold joints
8. Inspect Work — Check for solder bridges; verify polarity
9. Test Voltages — Before reconnecting to system, verify power supply outputs if applicable

Recommended Tools

• Temperature-controlled soldering iron (adjustable to 700°F / 370°C)
• Desoldering pump or solder wick
• Fine leaded solder (0.5 mm diameter)
• Isopropyl alcohol (90%+) and ESD-safe brush
• Digital multimeter
• Safety glasses
• Heat-resistant gloves

Voltage Verification After Recap

After power supply recap, measure output voltages before reconnecting to logic boards:

• +5V rail: 4.85V – 5.15V
• +12V rail: 11.9V – 12.7V
• -12V rail: Within 5% of nominal

ProFile Drive Power Supply

If you have a ProFile external hard drive, its power supply also contains RIFA capacitors and electrolytics that require replacement:

• RIFA safety capacitors (same X2 replacements as Lisa PSU)
• Electrolytic filter capacitors
• The ProFile is prone to the same RIFA failures as the Lisa

Additional Tips

• Use high-quality Japanese brand capacitors (Nichicon, Panasonic, Rubycon)
• Match or exceed original voltage ratings
• Observe temperature ratings—use 105°C rated capacitors for power supply work
• Take photos before and after for documentation
• Keep a log of parts used for future reference

Related Maintenance Pages

• Apple Lisa
• Apple Lisa General Maintenance
• Apple Lisa Troubleshooting
• CRT Discharge Procedure